[mythtvnz] Two PVR-150s, one works one doesn't - UPDATE

[Criggie]

The family is getting upset with no mythbox!

My next plan was to use ivtv 0.6.1 with kernel 2.6.16.11, as below.

ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.6.1 (tagged release) loading
ivtv:  Linux version: 2.6.16.11 PENTIUMIII gcc-4.0
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist. ivtv0:
Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 177
tveeprom 1-0050: Hauppauge model 26559, rev B260, serial# 8741972
tveeprom 1-0050: tuner model is LG S001D MK3 (idx 60, type 38)
tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)
(eeprom 0x74)
tveeprom 1-0050: audio processor is CX25843 (idx 37)
tveeprom 1-0050: decoder processor is CX25843 (idx 30)
tveeprom 1-0050: has radio, has no IR remote
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
ivtv0: Failed to load module cx25840
ivtv0: Failed to load module wm8775
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
total) ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB
total) ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB
total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers
(2048KB total)
ivtv0: Create encoder radio stream
tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c addr 0x44 not found for command 0x40045613!
ivtv0: i2c addr 0x44 not found for command 0xc0045627!
ivtv0: i2c hardware 0x00000020 not found for command 0x40345622!
ivtv0: i2c addr 0x44 not found for command 0x40345622!
ivtv0: i2c addr 0x44 not found for command 0x40045612!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c addr 0x44 not found for command 0x40045613!
ivtv0: i2c addr 0x44 not found for command 0x40045612!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv:  ======================  NEXT CARD  ======================
ivtv1: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 16 (level, low) -> IRQ 185
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
tda9887 2-0043: chip found @ 0x86 (ivtv i2c driver #1)
tveeprom 2-0050: The eeprom says no radio is present, but the tuner type
tveeprom 2-0050: indicates otherwise. I will assume that radio is present.
tveeprom 2-0050: Hauppauge model 26039, rev C1A5, serial# 7930897
tveeprom 2-0050: tuner model is TCL MPE05-2 (idx 105, type 38)
tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)
(eeprom 0x74)
tveeprom 2-0050: audio processor is CX25842 (idx 36)
tveeprom 2-0050: decoder processor is CX25842 (idx 29)
tveeprom 2-0050: has radio, has IR remote
ivtv1: Failed to load module cx25840
ivtv1: Failed to load module wm8775
ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv1: Encoder revision: 0x02050032
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
total) ivtv1: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB
total) ivtv1: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB
total) ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers
(2048KB total)
ivtv1: Create encoder radio stream
tuner 2-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv1: i2c addr 0x44 not found for command 0x40045613!
ivtv1: i2c addr 0x44 not found for command 0xc0045627!
ivtv1: i2c hardware 0x00000020 not found for command 0x40345622!
ivtv1: i2c addr 0x44 not found for command 0x40345622!
ivtv1: i2c addr 0x44 not found for command 0x40045612!
ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv1: i2c addr 0x44 not found for command 0x40045613!
ivtv1: i2c addr 0x44 not found for command 0x40045612!
ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv1: Initialized Hauppauge WinTV PVR-150, card #1
ivtv:  ====================  END INIT IVTV  ====================
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c addr 0x44 not found for command 0x40045613!
ivtv0: i2c addr 0x44 not found for command 0xc0045627!
ivtv0: i2c hardware 0x00000020 not found for command 0x40345622!
ivtv0: i2c addr 0x44 not found for command 0x40345622!
ivtv0: i2c addr 0x44 not found for command 0x40045612!

There's lots of the last 6 lines over and over whenever I access
/dev/video0 and /dev/video1

With 0.6.1 and kernel 2.6.16.11 I get a 0 byte file from   cat /dev/video0
> file.

Criggie wrote:
> Gidday all.  I've got a problem - I've added a second hauppauge PVR-150
to an existing mythtv backend machine.
>
> Now one tuner works fine, the other tuner returns only static, and appears
> to be loading things heavily when its in use.   I changed from ivtv
0.4.0 to 0.4.4 and that made no difference.
>
> The original card was a PVR-150 MCE variant, and the new one is a
PVR-150 retail version.  Both cards worked perfectly previously.
>
> I have used a splitter to provide both cards with a signal from the
aerial - I have tried swapping the leads so I know its not a simple
matter of cabling.
>
> Does anyone have any ideas?
>
>
> lspci says
> 0000:00:0a.0 Multimedia video controller: Internext Compression Inc
iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
> 0000:00:0c.0 Multimedia video controller: Internext Compression Inc
iTVC16 (CX23416) MPEG-2 Encoder (rev 01)

> Here's the relevant dmesg lines....
>
> ivtv:  ==================== START INIT IVTV ==================== ivtv: 
version 0.4.4 (tagged release) loading
> ivtv:  Linux version: 2.6.14.2 PENTIUMIII gcc-4.0
> ivtv:  In case of problems please include the debug info between ivtv: 
the START INIT IVTV and END INIT IVTV lines, along with
> ivtv:  any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
> ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 177
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
> wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
> tda9885/6/7: chip found @ 0x86
> ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
> tveeprom 1-0050: Hauppauge model 26039, rev C1A5, serial# 7930897
tveeprom 1-0050: tuner model is unknown (idx 105, type 0)
> tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom
> 0x74)
> tveeprom 1-0050: audio processor is CX25842 (idx 36)
> tveeprom 1-0050: decoder processor is CX25842 (idx 29)
> tveeprom 1-0050: has no radio, has IR remote
> cx25840 1-0044: ivtv driver
> cx25840 1-0044: cx25842-23 found @ 0x88 (ivtv i2c driver #0)
> cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
> ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
> ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
> ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
> ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
> tuner 1-0061: type set to 0 (Temic PAL (4002 FH5))
> ivtv0: Initialized WinTV PVR 150, card #0
> ivtv:  ======================  NEXT CARD  ====================== ivtv1:
Autodetected WinTV PVR 150 card (cx23416 based)
> ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 16 (level, low) -> IRQ 185
ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
> tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
> ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
> wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
> ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
> tda9885/6/7: chip found @ 0x86
> ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]
> cx25840 2-0044: ivtv driver
> cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
> cx25840 2-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
> ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
> tveeprom 2-0050: Hauppauge model 26559, rev B260, serial# 8741972
tveeprom 2-0050: tuner model is LG S001D MK3 (idx 60, type 38)
> tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom
> 0x74)
> tveeprom 2-0050: audio processor is CX25843 (idx 37)
> tveeprom 2-0050: decoder processor is CX25843 (idx 30)
> tveeprom 2-0050: has radio, has no IR remote
> ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv1: Encoder revision: 0x02050032
> ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
> ivtv1: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
> ivtv1: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
> ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
> ivtv1: Create encoder radio stream
> tuner 2-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
ivtv1: Initialized WinTV PVR 150, card #1
> ivtv:  ====================  END INIT IVTV  ====================




-- 
Criggie