[mythtvnz] Gentoo - persevere or try Knoppmyth?

[Robert Fisher]

On Thursday 05 October 2006 11:42 am, Nick Rout wrote:

> I did the same move : gentoo--> knoppmyth and have not looked back.
>
Well I am not having the same success.

Using Knoppmyth R5D1

After a fresh installation I go through the setup procedure and when I try to 
set the video source it locks the screen and seems to do nothing more.

Maybe I have a hardware compatability problem (with Knoppmyth)????

dmesg before and after setup are different.

dmesg before setup (immediately after installation)....
(Notice the Hauppauge WinTV PVR-150 is initialised then removed then 
initialised again.)

ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.7.0 (tagged release) loading
ivtv:  Linux version: 2.6.17-chw-8 SMP preempt mod_unload 586 gcc-3.4
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 20
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
tveeprom 1-0050: Hauppauge model 26559, rev B260, serial# 8432218
tveeprom 1-0050: tuner model is LG S001D MK3 (idx 60, type 38)
tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 
0x74)
tveeprom 1-0050: audio processor is CX25843 (idx 37)
tveeprom 1-0050: decoder processor is CX25843 (idx 30)
tveeprom 1-0050: has radio, has no IR remote
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB 
total)
ivtv0: Create encoder radio stream
tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv:  ====================  END INIT IVTV  ====================
ACPI: PCI interrupt for device 0000:00:0a.0 disabled
ivtv0: Removed Hauppauge WinTV PVR-150, card #0
ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.7.0 (tagged release) loading
ivtv:  Linux version: 2.6.17-chw-8 SMP preempt mod_unload 586 gcc-3.4
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 20
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
tveeprom 1-0050: Hauppauge model 26559, rev B260, serial# 8432218
tveeprom 1-0050: tuner model is LG S001D MK3 (idx 60, type 38)
tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 
0x74)
tveeprom 1-0050: audio processor is CX25843 (idx 37)
tveeprom 1-0050: decoder processor is CX25843 (idx 30)
tveeprom 1-0050: has radio, has no IR remote
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB 
total)
ivtv0: Create encoder radio stream
tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv:  ====================  END INIT IVTV  ====================
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present


dmesg after setup (locks up)....

ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.7.0 (tagged release) loading
ivtv:  Linux version: 2.6.17-chw-8 SMP preempt mod_unload 586 gcc-3.4
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 20
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
tveeprom 1-0050: Hauppauge model 26559, rev B260, serial# 8432218
tveeprom 1-0050: tuner model is LG S001D MK3 (idx 60, type 38)
tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 
0x74)
tveeprom 1-0050: audio processor is CX25843 (idx 37)
tveeprom 1-0050: decoder processor is CX25843 (idx 30)
tveeprom 1-0050: has radio, has no IR remote
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB 
total)
ivtv0: Create encoder radio stream
tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv:  ====================  END INIT IVTV  ====================
cx25840 1-0044: 0x0000 is not a valid video input!