<div dir="ltr"><div>I wonder whether one of those CapSense things might work <a href="http://www.cypress.com/products/capsense-controllers">http://www.cypress.com/products/capsense-controllers</a><br><br></div>Another approach might be running the capacitor as part of an RC oscillator and measuring the frequency.<br></div><div class="gmail_extra"><br><div class="gmail_quote">On Wed, Nov 18, 2015 at 2:05 PM, Robin Gilks <span dir="ltr"><<a href="mailto:robin@gilks.org" target="_blank">robin@gilks.org</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Well I was going to write something like that - but my ideas just sort of<br>
dissolved...<br>
<br>
If I keep coming back to this project at the correct Frequency, I'll find<br>
out if I have the Capacity for it to get finished.<br>
<br>
After all my work, it appears that Resistance is futile...<br>
<span class="im HOEnZb"><br>
<br>
<br>
> Shouldn't the subj be 'Just when I though I had a Solution for soil<br>
> Moisture" ? :)<br>
><br>
> On 18/11/2015 12:40 p.m., Robin Gilks wrote:<br>
>> ... I discovered that rather than resistive I should be looking at high<br>
>> frequency capacitive sensors.<br>
>><br>
>> Commercial ones run at up to 70MHz, this one based on am ATTINY441 AVR<br>
>> chip runs at the system clock rate of 16MHz and has an I2C interface.<br>
>><br>
>> <a href="https://www.tindie.com/products/miceuz/i2c-soil-moisture-sensor/" rel="noreferrer" target="_blank">https://www.tindie.com/products/miceuz/i2c-soil-moisture-sensor/</a><br>
>><br>
>> Very simple mode of operation, its basically using the PCB as the two<br>
>> plates of a capacitor and as the dielectric constant around it changes<br>
>> (due to moisture) so does the capacitance.<br>
>><br>
>> This is measured by driving a high frequency clock to the cap through a<br>
>> series resistor and measuring the peak voltage swing across the cap with<br>
>> a<br>
>> couple of diodes and long(ish) time constant RC network providing a<br>
>> differential output to the A/D inputs of the micro.<br>
>><br>
>> Think I'll go this route...<br>
>><br>
<br>
<br>
<br>
</span><span class="HOEnZb"><font color="#888888">--<br>
Robin Gilks<br>
</font></span><div class="HOEnZb"><div class="h5"><br>
<br>
_______________________________________________<br>
Chchrobotics mailing list <a href="mailto:Chchrobotics@lists.linuxnut.co.nz">Chchrobotics@lists.linuxnut.co.nz</a><br>
<a href="http://lists.ourshack.com/mailman/listinfo/chchrobotics" rel="noreferrer" target="_blank">http://lists.ourshack.com/mailman/listinfo/chchrobotics</a><br>
Mail Archives: <a href="http://lists.ourshack.com/pipermail/chchrobotics/" rel="noreferrer" target="_blank">http://lists.ourshack.com/pipermail/chchrobotics/</a><br>
Meetings usually 3rd Monday each month. See <a href="http://kiwibots.org" rel="noreferrer" target="_blank">http://kiwibots.org</a> for venue, directions and dates.<br>
When replying, please edit your Subject line to reflect new subjects.<br>
</div></div></blockquote></div><br></div>