<p dir="ltr">If a centre hole is acceptable then you could use a hole saw. I have had good results cutting ABS. I used a good quality arbor and saw with 3 cutting teeth, not the ones with serrations.</p>
<p dir="ltr">Spencer</p>
<div class="gmail_quote">On 27 Nov 2014 14:34, "Winston Wealleans" <<a href="mailto:winstonhw@clear.net.nz">winstonhw@clear.net.nz</a>> wrote:<br type="attribution"><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">At 01:46 p.m. 27/11/2014, you wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
I am looking for disks about 50-70mm dia, 5-15mm thick, and about 100<br>
of them...  I need a notch and 2 holes in them too, but that's easily<br>
taken care of.<br>
<br>
The straightforward option would be to slice up a 50mm dia wooden pole<br>
or dowel, but plastic would be better because of the lower weight.<br>
Perhaps something like a tooth wheel from a mechanical toy set. The<br>
teeth on the disk would not be a problem.<br>
<br>
Getting it laser cut is likely not cheap enough, and solid plastic<br>
probably weighs more than pine too.<br>
</blockquote>
<br>
Give Carl Pavletich  at 21 388 245 a call.<br>
<a href="http://www.fablabxchc.org.nz/welcome/" target="_blank">http://www.fablabxchc.org.nz/<u></u>welcome/</a><br>
they have a big nice new laser cutter that will handle MDF, cardboard, fabrics and all sorts of plastics<br>
<br>
Stress that you are a tinkerer and Robotics Group member.<br>
<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Has anyone come across something suitable that might be put to use with<br>
a bit of drilling and hacksawing?<br>
<br>
Thanks muchly,<br>
<br>
Volker<br>
</blockquote>
<br>
<br>
---<br>
This email has been checked for viruses by Avast antivirus software.<br>
<a href="http://www.avast.com" target="_blank">http://www.avast.com</a><br>
<br>
<br>
______________________________<u></u>_________________<br>
Chchrobotics mailing list <a href="mailto:Chchrobotics@lists.linuxnut.co.nz" target="_blank">Chchrobotics@lists.linuxnut.<u></u>co.nz</a><br>
<a href="http://lists.ourshack.com/mailman/listinfo/chchrobotics" target="_blank">http://lists.ourshack.com/<u></u>mailman/listinfo/chchrobotics</a><br>
Mail Archives: <a href="http://lists.ourshack.com/pipermail/chchrobotics/" target="_blank">http://lists.ourshack.com/<u></u>pipermail/chchrobotics/</a><br>
Web site: <a href="http://kiwibots.org" target="_blank">http://kiwibots.org</a><br>
Meetings 3rd Monday each month.<br>
<br>
When replying, please edit your Subject line to reflect new content.<br>
</blockquote></div>